Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 60 years of experience in producing some of the finest capacitors available today. TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6. Contains four 8-pin sockets, four "bear trap" retainers, eight mounting screws, four 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and four carbon composition 1500 ohm control grid resistors. CAPACITOR, F&T BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made in Germany.
Bolts screw into a captive nut on the top rail of the chassis, so there are no bottom nuts on these models.
CAPACITOR, ILLINOIS CAPACITOR BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Illinois Capacitor Company was founded in 1934 in Chicago, IL, and over 80 years later continues to produce benchmark quality capacitors for industry. Perfect for amplifier circuit additions or modifications. Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug. Introduced on Blonde, Brown, and Blackface-era Fender amplifiers. Introduced on some Blonde and Brownface-era Fender amplifiers. High quality black EXTRA-THICK leather handle for vintage Fender and Ampeg amps. New original Fender reproduction, for the blackface era (1960s). Fender logo with "tail", cast metal, mounting screws included.
Illinois Capacitor is now a subsidiary of Cornell Dubilier, another American capacitor manufacturer tracing its roots to 1909. Replacement for Fender main filter capacitor on Princeton Reverb II, Deluxe Reverb II, Bassman 20, Super Champ, and Champ II from the 1980s. OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN THE HEAD OF THE Fender BACK PANEL SCREWS. OD 7/16", ID 3/16" Typically found on the back panel of some Fender Blackface/Silverface vintage amps and the reissues of those amps. OD 7/16", ID 3/16" Typically found on the back panel of some Fender Blackface/Silverface vintage amps and the reissues of those amps. End terminals on each strip are the mounting lugs, so they become a ground lug if attached to a metal chassis. Used on '65 Twin Reverb, '65 Deluxe Reverb, '65 Super Reverb, '65 Princeton Reverb, '64 Vibroverb Custom, Custom Vibrolux, Vibro-King 212 Enclosure, Blues Junior, Pro Junior, Acoustasonic Jr. Note: This handle is quite thick - 0.4 inches thick (about 3/8", or 10mm). Used on the upper left corner of the grill cloth on most blackface era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall.
These dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Princeton and Princeton Reverb do not need the resistors. Do not install in an amplifier that does not have a standby switch - always use the standby switch in amps so equipped when using the 5SSR.
This is a great kit to replaced all 6 of the tube shields in many Fender amps with 6 preamp tubes. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Contains two 8-pin sockets, two "bear trap" retainers, four mounting screws, two 470 ohm screen grid resistors (Metal-Film Flameproof for safety), and two carbon composition 1500 ohm control grid resistors. 1.31" diameter, 0.89" tall (not including pins and center post).necessary that a standby switch is used in conjunction with this device.